Kjører Computer Fans alltid på 100% med mindre annet er sagt?

Innholdsfortegnelse:

Kjører Computer Fans alltid på 100% med mindre annet er sagt?
Kjører Computer Fans alltid på 100% med mindre annet er sagt?

Video: Kjører Computer Fans alltid på 100% med mindre annet er sagt?

Video: Kjører Computer Fans alltid på 100% med mindre annet er sagt?
Video: The spyware spooks use to hack mobiles - BBC Click - YouTube 2024, Mars
Anonim
Enten på bærbare datamaskiner, skrivebord eller spillkonsoller, har vi alle hørt whir av systemets fans i bakgrunnen. Hvor nøyaktig vet alle disse små kjølevifter når de skal spinne opp, ned og ellers moderere mengden luft de flytter?
Enten på bærbare datamaskiner, skrivebord eller spillkonsoller, har vi alle hørt whir av systemets fans i bakgrunnen. Hvor nøyaktig vet alle disse små kjølevifter når de skal spinne opp, ned og ellers moderere mengden luft de flytter?

Dagens Spørsmål og svar sesjon kommer til oss med høflighet av SuperUser, en underavdeling av Stack Exchange, en fellesskapsdrevet gruppering av Q & A-nettsteder.

Spørsmålet

SuperUser leser darkAsPitch lurer på:

What happens if I do not plug it into the motherboard and it does not have a switch?

I have seen fans before with an “off/low/high” switch that allows you to manually set their speed.

I have seen fans that plug into the motherboard and are controlled by the OS.

I am curious… what does a fan do by default when plugged into a PSU? Does it run at 100% unless otherwise told to go slower? This is what I would expect…

Så hvordan fungerer de? Full boring med mindre annet er påbudt?

Svaret

SuperUser bidragsyter Journeyman Geek tilbyr følgende innsikt:

Well, kind of. Fan speed control is done by varying voltage or through Pulse Width Modulation (using a constant voltage and cutting it up into pulses to vary speed). If you’re plugged into a motherboard, that’s what it does. If it has 3 wires, the third wire tells the motherboard what’s the speed the fan is running as. If you have a 4th wire, fan speed control is done via PWM rather than voltage control.

You can plug in a 2 wire fan to a 3 or 4 wire connector (though you lose speed feed back), and a 3 wire to a 4 wire connector (where you lose PWM control). You can also use a fan controller to control speeds.

Else, assuming the power source is unaware it’s a fan (as it would be connected through molex for example), and is at a fixed voltage, yes, it goes at full speed all the time.

Medforfatter Hyperslug fremhever hvordan unntakene utspiller seg:

Like the other guys said, pretty much yes, but I can think of 3 exceptions:

1. A few fans have a built in thermistor that will adjust speed depending on temperature.

2. PSU’s with specially marked Fan-Only PSU connectors (Antec TruePower 550W) can adjust the speed of the fan:

3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.
3. If you plug it into the PSU molex using the 12/5 volt rails (7 volt) or 12/7 rails (5 volt) it’ll be run slower, but at this point you’re modding.

Og der har du det: Uten ekstern kontroll ved hjelp av en hvilken som helst mekanisme (det være seg hovedkortets input, et case termometer eller en intelligent PSU), vil fansen kjøre med høyeste hastighet strømkilden tillater.

Har du noe å legge til forklaringen? Lyde av i kommentarene. Vil du lese flere svar fra andre tech-savvy Stack Exchange-brukere? Sjekk ut hele diskusjonstråden her.

Anbefalt: